Do the following if your Whirlpool refrigerator is freezing everything:
To reset the temperature of a Whirlpool refrigerator, locate the reset controls on the refrigerator. Find the refrigerator temperature control buttons and press (+) or (-) until the desired temperature level appears. Then leave it on for a few hours.
The refrigerator may just need a reset or adjustment of its settings. It tends to freeze if the temperature is too high. Moderate temperature is between 390F and 400F. Check your refrigerator's user manual to see how it fits correctly.
You can let it run for about 8 hours to check if you have the correct settings. If it continues to freeze, you will need to readjust it. But in case you are not sure how to reset it, ask a refrigerator expert to do it fyor ou - shymon.
On some Whirlpool refrigerator models, the freezer temperature control sets the refrigerator temperature. Therefore, check the temperature range to know the exact temperature of the compartments.
To ensure the thermistor is working, unplug the refrigerator and gently pull on the control box on the roof of the refrigerator to access the thermistor. Check for loose or damaged cables. If there is none, use a multimeter to check the resistance level of the thermistor.
Connect the thermistor lead to the multimeter. Get the technology/resistor sheet for your refrigerator model, then place the thermistor in a cup of ice.
If the resistance reading has more than a 10% variation from what appears on the sheet, it means that the thermistor is still working. However, it does not show the resistance level, it is defective.
The control board regulates the temperature based on the thermistor readings. If it is defective, the evaporator and condenser will continue to operate without any regulation. As a result, the temperature freezes.
Additionally, it can detect a working thermistor if it changes when the refrigerator temperature is adjusted. If it doesn't, it means it is defective and needs replacement.
To check the condenser coils, locate them under or at the back of the refrigerator, remove the grates, and then clean or dry the coils with a vacuum cleaner.
The condenser coils could be blocked, obstructing heat output to the refrigerator. When they are dusty or dirty, they put more pressure on the coils and make them work harder to maintain a steady temperature. As a result, they begin to freeze everything that is put in the refrigerator.
However, if you notice that the condenser coils continue to malfunction after cleaning them, it is advisable to replace them urgently so that they do not cause further problems.
Make sure there is nothing blocking the vents so that cold air can flow freely around the unit. Otherwise, some parts of the unit will freeze food and others will not.
You can also clean the vents if there are food particles around them. To clean the vents, remove the screws and carefully remove the vents. Then use a damp towel to clean the grates and other areas, and carefully reattach the grates.
Ventilation grilles allow free air flow from the different compartments. Once they become blocked with food particles or dirt, the flow is disturbed and can cause freezing. Likewise, it could cause an increase in humidity and odors in the refrigerator.
Therefore, make sure you always keep it clean and do not place anything in front of it while stacking your refrigerator.
Depending on the type of Whirlpool refrigerator you have, the vents may be located on the back wall, bottom, or left side of the refrigerator.
To inspect the damper assembly, unplug the refrigerator, carefully remove the shelves, allow the refrigerator to dry, and then place your hand on the damper assembly to check for cold air coming out of the freezer.
When it is stuck or open, it increases the amount of cold air entering the refrigerator from the freezer. As a result, anything you put in it can start to freeze.
Once you notice it, check if it is completely damaged or just needs a reset. However, fixing a new shock absorber can be done in a few steps.
Purchase one that fits your Whirlpool refrigerator model, remove the compartments from the refrigerator shelves, locate the damper control, and then carefully remove the lid and water filter. After this, locate the tabs, loosen the screws, remove the old one, and then install the new one before reattaching the screws.
After fixing it, close the refrigerator door and try to test it to see if it is fixed properly.
If the problem persists, contact Whirlpool service center for service or a professional refrigerator repair agent to help you solve the problem.
To inspect the control panel of your Whirlpool refrigerator, plug in the refrigerator, find the control panel on the back of the refrigerator, carefully loosen the screws with a screwdriver. Be sure not to touch the cables with your bare hands.
Next, locate the voltage cable and place a meter on it to check if it is still working.
The control panel is the machine room of the refrigerator. It is responsible for the transmission and regulation of voltage to the refrigerator components.
If it malfunctions, it can allow a continuous flow of high voltage to the refrigerants for a long time, causing the release of excess ice.
However, to inspect this, make sure the other components have been checked and are working properly.
To check your refrigerator door gasket, open the door and close it on a dollar bill. If the bill falls out, it means that the door seal is loose, but if it falls out, the door seal is still intact.
Carefully check the door gaskets for leaks or looseness. Additionally, cold air may escape from the refrigerator if the gasket is worn, broken, or deformed. It is necessary to act immediately in this situation to save gas as well as energy.